dactyl-manuform/guide
2016-09-10 22:57:49 +02:00
..
application-of-switches-and-caps.jpg makeup changes, replaced the 2 new pictures 2016-09-06 22:31:10 +02:00
circuit-diagram.png improvements on Route 2 2016-09-10 22:57:49 +02:00
hotglue-left-hand.jpg Add very rough guide 2015-12-10 11:28:02 +08:00
left-hand-mcp-1.jpg Add very rough guide 2015-12-10 11:28:02 +08:00
left-hand-mcp-2.jpg Add very rough guide 2015-12-10 11:28:02 +08:00
left-hand-pcb-pyralux.png Add very rough guide 2015-12-10 11:28:02 +08:00
madness.jpg Add very rough guide 2015-12-10 11:28:02 +08:00
README.md Add very rough guide 2015-12-10 11:28:02 +08:00
README.org improvements on Route 2 2016-09-10 22:57:49 +02:00
right-hand-pcb-1.jpg Add very rough guide 2015-12-10 11:28:02 +08:00
right-hand-pcb-pyralux.png Add very rough guide 2015-12-10 11:28:02 +08:00
right-hand-pcb-with-teensy.jpg Add very rough guide 2015-12-10 11:28:02 +08:00
rows-and-columns-connected-to-chips.jpg Route 2 upgraded 2016-09-10 22:38:06 +02:00
teensy-1.jpg Add very rough guide 2015-12-10 11:28:02 +08:00
teensy-2-fuxor-reziztorrs.jpg Add very rough guide 2015-12-10 11:28:02 +08:00
wiring-create-columns-left.jpg Route 2 upgraded 2016-09-10 22:38:06 +02:00
wiring-create-columns-right.jpg Route 2 upgraded 2016-09-10 22:38:06 +02:00
wiring-create-rows-both-sides.jpg added the first part of route 2, creating the rows 2016-09-08 09:14:39 +02:00
wiring-create-rows-testing.jpg added the first part of route 2, creating the rows 2016-09-08 09:14:39 +02:00
wiring_create_rows.jpg added the first part of route 2, creating the rows 2016-09-08 09:14:39 +02:00
workbench.jpg Add very rough guide 2015-12-10 11:28:02 +08:00

Dactyl Flexible PCB Rough Guide

For now, take a look at the images and try to figure things out, I know that's not great (it's better than nothing!)

Making the PCB

Get two sheets of 6in square Pyralux™. Use the Toner Transfer method to etch the Pyralux sheets as you would a usual PCB

NOTE: If you only have an Inkjet make photocopies of the print out, voilà Toner based copies!

Here's a handy toner transfer guide ...

Print these PCB designs out...

Left hand:

Right hand:

When you're done etching, you'll need to carefully cut the pcb into pieces... See the images below.

This is Madness...

The thumb cluster pcb for the left hand:

Solder the MCP like so:

Solder the Teensy 2.0 like so:

Some interesting pull up 10k resistor business here... (TODO add a small diagram and notes)

Each hand of the keyboard will wire up like so:

Teensy goes here... note the rows soldered to the teensy via the Pyralux:

Here the left hand:

That's all for now, this guide will improve over time! (TODO!)