update profiles

filament/eSUN PLA+ 0.4 nozzle @Croesus.info

@@ -1,4 +1,4 @@
-sync_info = create
+sync_info = update
 user_id = 
 setting_id = 
 base_id = GFSA04

filament/eSUN PLA+ 0.4 nozzle @Croesus.json

@@ -21,7 +21,7 @@
         "25.95"
     ],
     "filament_flow_ratio": [
-        "0.97"
+        "0.975"
     ],
     "filament_max_volumetric_speed": [
         "28"
@@ -39,11 +39,17 @@
     "inherits": "My Generic PLA",
     "is_custom_defined": "0",
     "name": "eSUN PLA+ 0.4 nozzle @Croesus",
+    "nozzle_temperature": [
+        "210"
+    ],
+    "nozzle_temperature_initial_layer": [
+        "210"
+    ],
     "nozzle_temperature_range_low": [
         "210"
     ],
     "pressure_advance": [
-        "0.029"
+        "0.031"
     ],
     "slow_down_layer_time": [
         "15"

filament/eSUN PLA+ 0.4 nozzle @Jensen.json

@@ -1,6 +1,6 @@
 {
     "filament_settings_id": [
-        "eSUN PLA+ 0.4 nozzle @TzKal-Zuk"
+        "eSUN PLA+ 0.4 nozzle @Jensen"
     ],
     "from": "User",
     "hot_plate_temp": [
@@ -11,6 +11,6 @@
     ],
     "inherits": "Creality Generic PLA @Ender-3V3-all",
     "is_custom_defined": "0",
-    "name": "eSUN PLA+ 0.4 nozzle @TzKal-Zuk",
+    "name": "eSUN PLA+ 0.4 nozzle @Jensen",
     "version": "2.2.0.4"
 }

filament/eSUN PLA+ 0.6 nozzle @Croesus.info

@@ -1,4 +1,4 @@
-sync_info = create
+sync_info = update
 user_id = 
 setting_id = 
 base_id = GFSA04

filament/eSUN PLA+ 0.6 nozzle @Croesus.json

@@ -39,11 +39,17 @@
     "inherits": "My Generic PLA",
     "is_custom_defined": "0",
     "name": "eSUN PLA+ 0.6 nozzle @Croesus",
+    "nozzle_temperature": [
+        "210"
+    ],
+    "nozzle_temperature_initial_layer": [
+        "210"
+    ],
     "nozzle_temperature_range_low": [
         "210"
     ],
     "pressure_advance": [
-        "0.022"
+        "0.021"
     ],
     "slow_down_layer_time": [
         "15"

machine/Jensen 0.4 nozzle.json

@@ -6,8 +6,8 @@
     "inherits": "Creality Ender-3 V3 SE 0.4 nozzle",
     "is_custom_defined": "0",
     "machine_start_gcode": "M220 S100 ;Reset Feedrate \nM221 S100 ;Reset Flowrate \nM413 S0;Disables power loss recovery\n \nM104 S[nozzle_temperature_initial_layer] ;Set final nozzle temp \nM190 S[bed_temperature_initial_layer_single] ;Set and wait for bed temp to stabilize \nG28 ;Home \nM420 S1 ;Enable mesh leveling\nG92 E0 ;Reset Extruder \nG1 Z2.0 F3000 ;Move Z Axis up \nG1 X-2.1 Y20 Z0.28 F5000.0 ;Move to start position \nM109 S[nozzle_temperature_initial_layer] ;Wait for nozzle temp to stabilize \nG1 X-2.1 Y145.0 Z0.28 F1500.0 E15 ;Draw the first line \nG1 X-2.4 Y145.0 Z0.28 F5000.0 ;Move to side a little \nG1 X-2.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line \nG92 E0  ;Reset Extruder \nG1 E-1.0000 F1800 ;Retract a bit \nG1 Z2.0 F3000 ;Move Z Axis up \nG1 E0.0000 F1800",
-    "name": "TzKal-Zuk 0.4 nozzle",
+    "name": "Jensen 0.4 nozzle",
-    "printer_settings_id": "TzKal-Zuk 0.4 nozzle",
+    "printer_settings_id": "Jensen 0.4 nozzle",
     "retraction_length": [
         "0.8"
     ],

process/0.08mm @Croesus.info

@@ -1,4 +1,4 @@
-sync_info = update
+sync_info = create
 user_id = 
 setting_id = 
 base_id = GP004

process/0.08mm @Croesus.json

@@ -18,13 +18,13 @@
     "ironing_spacing": "0.2",
     "ironing_speed": "180",
     "is_custom_defined": "0",
-    "name": "0.08mm Extra Fine @Croesus",
+    "name": "0.08mm @Croesus",
     "only_one_wall_first_layer": "1",
     "only_one_wall_top": "1",
     "outer_wall_acceleration": "1000",
     "outer_wall_speed": "80",
     "precise_outer_wall": "1",
-    "print_settings_id": "0.08mm Extra Fine @Croesus",
+    "print_settings_id": "0.08mm @Croesus",
     "skirt_height": "2",
     "skirt_loops": "1",
     "skirt_speed": "0",

process/0.12mm @Croesus.info

@@ -1,4 +1,4 @@
-sync_info = update
+sync_info = create
 user_id = 
 setting_id = 
 base_id = GP004

process/0.12mm @Croesus.json

@@ -18,13 +18,13 @@
     "ironing_spacing": "0.2",
     "ironing_speed": "180",
     "is_custom_defined": "0",
-    "name": "0.12mm Fine @Croesus",
+    "name": "0.12mm @Croesus",
     "only_one_wall_first_layer": "1",
     "only_one_wall_top": "1",
     "outer_wall_acceleration": "1000",
     "outer_wall_speed": "80",
     "precise_outer_wall": "1",
-    "print_settings_id": "0.12mm Fine @Croesus",
+    "print_settings_id": "0.12mm @Croesus",
     "skirt_height": "2",
     "skirt_loops": "1",
     "skirt_speed": "0",

process/0.12mm @Jensen.info

@@ -1,4 +1,4 @@
-sync_info = update
+sync_info = create
 user_id = 
 setting_id = 
 base_id = GP004

process/0.12mm @Jensen.json

@@ -0,0 +1,18 @@
+{
+    "bottom_surface_pattern": "monotonicline",
+    "from": "User",
+    "inherits": "0.12mm Fine @Creality Ender3V3SE 0.4",
+    "initial_layer_print_height": "0.28",
+    "internal_solid_infill_pattern": "monotonicline",
+    "is_custom_defined": "0",
+    "name": "0.12mm @Jensen",
+    "only_one_wall_first_layer": "1",
+    "only_one_wall_top": "1",
+    "precise_outer_wall": "1",
+    "print_settings_id": "0.12mm @Jensen",
+    "skirt_loops": "1",
+    "sparse_infill_density": "40%",
+    "sparse_infill_pattern": "gyroid",
+    "version": "2.2.0.4",
+    "wall_generator": "classic"
+}

process/0.12mm Fine @TzKal-Zuk.json

@@ -1,49 +0,0 @@
-{
-    "bottom_solid_infill_flow_ratio": "1.05",
-    "bottom_surface_pattern": "monotonicline",
-    "bridge_flow": "1",
-    "bridge_speed": "60",
-    "detect_thin_wall": "0",
-    "enable_overhang_speed": "0",
-    "from": "User",
-    "gap_infill_speed": "15",
-    "inherits": "0.12mm Fine @Creality Ender3V3SE 0.4",
-    "initial_layer_infill_speed": "30",
-    "initial_layer_line_width": "120%",
-    "initial_layer_print_height": "0.28",
-    "initial_layer_speed": "15",
-    "inner_wall_acceleration": "1000",
-    "inner_wall_line_width": "110%",
-    "inner_wall_speed": "60",
-    "internal_bridge_speed": "80",
-    "internal_solid_infill_line_width": "120%",
-    "internal_solid_infill_pattern": "monotonicline",
-    "internal_solid_infill_speed": "100",
-    "is_custom_defined": "0",
-    "line_width": "110%",
-    "max_volumetric_extrusion_rate_slope": "15",
-    "name": "0.12mm Fine @TzKal-Zuk",
-    "only_one_wall_first_layer": "1",
-    "only_one_wall_top": "1",
-    "outer_wall_acceleration": "500",
-    "outer_wall_line_width": "100%",
-    "outer_wall_speed": "40",
-    "precise_outer_wall": "1",
-    "print_settings_id": "0.12mm Fine @TzKal-Zuk",
-    "skirt_loops": "1",
-    "small_perimeter_speed": "15",
-    "sparse_infill_acceleration": "200%",
-    "sparse_infill_density": "40%",
-    "sparse_infill_line_width": "160%",
-    "sparse_infill_pattern": "gyroid",
-    "sparse_infill_speed": "150",
-    "support_line_width": "96%",
-    "support_speed": "60",
-    "top_surface_acceleration": "1000",
-    "top_surface_line_width": "100%",
-    "top_surface_speed": "30",
-    "travel_acceleration": "3500",
-    "version": "2.2.0.4",
-    "wall_generator": "classic",
-    "wall_loops": "3"
-}

process/0.16mm @Croesus.info

@@ -1,4 +1,4 @@
-sync_info = update
+sync_info = create
 user_id = 
 setting_id = 
 base_id = GP004

process/0.16mm @Croesus.json

@@ -18,13 +18,13 @@
     "ironing_spacing": "0.2",
     "ironing_speed": "180",
     "is_custom_defined": "0",
-    "name": "0.16mm Optimal @Croesus",
+    "name": "0.16mm @Croesus",
     "only_one_wall_first_layer": "1",
     "only_one_wall_top": "1",
     "outer_wall_acceleration": "1000",
     "outer_wall_speed": "80",
     "precise_outer_wall": "1",
-    "print_settings_id": "0.16mm Optimal @Croesus",
+    "print_settings_id": "0.16mm @Croesus",
     "skirt_height": "2",
     "skirt_loops": "1",
     "skirt_speed": "0",

process/0.16mm @Jensen.info

@@ -1,4 +1,4 @@
-sync_info = update
+sync_info = create
 user_id = 
 setting_id = 
 base_id = GP004

process/0.16mm @Jensen.json

@@ -0,0 +1,18 @@
+{
+    "bottom_surface_pattern": "monotonicline",
+    "from": "User",
+    "inherits": "0.16mm Optimal @Creality Ender3V3SE 0.4",
+    "initial_layer_print_height": "0.28",
+    "internal_solid_infill_pattern": "monotonicline",
+    "is_custom_defined": "0",
+    "name": "0.16mm @Jensen",
+    "only_one_wall_first_layer": "1",
+    "only_one_wall_top": "1",
+    "precise_outer_wall": "1",
+    "print_settings_id": "0.16mm @Jensen",
+    "skirt_loops": "1",
+    "sparse_infill_density": "40%",
+    "sparse_infill_pattern": "gyroid",
+    "version": "2.2.0.4",
+    "wall_generator": "classic"
+}

process/0.16mm Optimal @TzKal-Zuk.json

@@ -1,49 +0,0 @@
-{
-    "bottom_solid_infill_flow_ratio": "1.05",
-    "bottom_surface_pattern": "monotonicline",
-    "bridge_flow": "1",
-    "bridge_speed": "60",
-    "detect_thin_wall": "0",
-    "enable_overhang_speed": "0",
-    "from": "User",
-    "gap_infill_speed": "15",
-    "inherits": "0.16mm Optimal @Creality Ender3V3SE 0.4",
-    "initial_layer_infill_speed": "30",
-    "initial_layer_line_width": "120%",
-    "initial_layer_print_height": "0.28",
-    "initial_layer_speed": "15",
-    "inner_wall_acceleration": "1000",
-    "inner_wall_line_width": "110%",
-    "inner_wall_speed": "60",
-    "internal_bridge_speed": "80",
-    "internal_solid_infill_line_width": "120%",
-    "internal_solid_infill_pattern": "monotonicline",
-    "internal_solid_infill_speed": "100",
-    "is_custom_defined": "0",
-    "line_width": "110%",
-    "max_volumetric_extrusion_rate_slope": "15",
-    "name": "0.16mm Optimal @TzKal-Zuk",
-    "only_one_wall_first_layer": "1",
-    "only_one_wall_top": "1",
-    "outer_wall_acceleration": "500",
-    "outer_wall_line_width": "100%",
-    "outer_wall_speed": "40",
-    "precise_outer_wall": "1",
-    "print_settings_id": "0.16mm Optimal @TzKal-Zuk",
-    "skirt_loops": "1",
-    "small_perimeter_speed": "15",
-    "sparse_infill_acceleration": "200%",
-    "sparse_infill_density": "40%",
-    "sparse_infill_line_width": "160%",
-    "sparse_infill_pattern": "gyroid",
-    "sparse_infill_speed": "150",
-    "support_line_width": "96%",
-    "support_speed": "60",
-    "top_surface_acceleration": "1000",
-    "top_surface_line_width": "100%",
-    "top_surface_speed": "30",
-    "travel_acceleration": "3500",
-    "version": "2.2.0.4",
-    "wall_generator": "classic",
-    "wall_loops": "3"
-}

process/0.20mm @Croesus.info

@@ -1,4 +1,4 @@
-sync_info = update
+sync_info = create
 user_id = 
 setting_id = 
 base_id = GP004

process/0.20mm @Croesus.json

@@ -18,13 +18,13 @@
     "ironing_spacing": "0.2",
     "ironing_speed": "180",
     "is_custom_defined": "0",
-    "name": "0.20mm Standard @Croesus",
+    "name": "0.20mm @Croesus",
     "only_one_wall_first_layer": "1",
     "only_one_wall_top": "1",
     "outer_wall_acceleration": "1000",
     "outer_wall_speed": "80",
     "precise_outer_wall": "1",
-    "print_settings_id": "0.20mm Standard @Croesus",
+    "print_settings_id": "0.20mm @Croesus",
     "skirt_height": "2",
     "skirt_loops": "1",
     "skirt_speed": "0",

process/0.20mm @Jensen.info

@@ -1,4 +1,4 @@
-sync_info = update
+sync_info = create
 user_id = 
 setting_id = 
 base_id = GP004

process/0.20mm @Jensen.json

@@ -0,0 +1,19 @@
+{
+    "bottom_surface_pattern": "monotonicline",
+    "from": "User",
+    "inherits": "0.20mm Standard @Creality Ender3V3SE 0.4",
+    "initial_layer_print_height": "0.28",
+    "internal_solid_infill_pattern": "monotonicline",
+    "is_custom_defined": "0",
+    "name": "0.20mm @Jensen",
+    "only_one_wall_first_layer": "1",
+    "only_one_wall_top": "1",
+    "precise_outer_wall": "1",
+    "print_settings_id": "0.20mm @Jensen",
+    "skirt_loops": "1",
+    "sparse_infill_density": "40%",
+    "sparse_infill_pattern": "gyroid",
+    "top_surface_line_width": "0.4",
+    "version": "2.2.0.4",
+    "wall_generator": "classic"
+}

process/0.20mm Standard @TzKal-Zuk.info

@@ -1,5 +0,0 @@
-sync_info = update
-user_id = 
-setting_id = 
-base_id = GP004
-updated_time = 1733885975

process/0.20mm Standard @TzKal-Zuk.json

@@ -1,51 +0,0 @@
-{
-    "bottom_shell_layers": "3",
-    "bottom_solid_infill_flow_ratio": "1.05",
-    "bottom_surface_pattern": "monotonicline",
-    "bridge_flow": "1",
-    "bridge_speed": "60",
-    "detect_thin_wall": "0",
-    "enable_overhang_speed": "0",
-    "from": "User",
-    "gap_infill_speed": "15",
-    "inherits": "0.20mm Standard @Creality Ender3V3SE 0.4",
-    "initial_layer_infill_speed": "30",
-    "initial_layer_line_width": "120%",
-    "initial_layer_print_height": "0.28",
-    "initial_layer_speed": "15",
-    "inner_wall_acceleration": "1000",
-    "inner_wall_line_width": "110%",
-    "inner_wall_speed": "60",
-    "internal_bridge_speed": "80",
-    "internal_solid_infill_line_width": "120%",
-    "internal_solid_infill_pattern": "monotonicline",
-    "internal_solid_infill_speed": "100",
-    "is_custom_defined": "0",
-    "line_width": "110%",
-    "max_volumetric_extrusion_rate_slope": "15",
-    "minimum_sparse_infill_area": "15",
-    "name": "0.20mm Standard @TzKal-Zuk",
-    "only_one_wall_first_layer": "1",
-    "only_one_wall_top": "1",
-    "outer_wall_acceleration": "500",
-    "outer_wall_line_width": "100%",
-    "outer_wall_speed": "40",
-    "precise_outer_wall": "1",
-    "print_settings_id": "0.20mm Standard @TzKal-Zuk",
-    "skirt_loops": "1",
-    "small_perimeter_speed": "15",
-    "sparse_infill_acceleration": "200%",
-    "sparse_infill_density": "40%",
-    "sparse_infill_line_width": "160%",
-    "sparse_infill_pattern": "gyroid",
-    "sparse_infill_speed": "150",
-    "support_line_width": "96%",
-    "support_speed": "60",
-    "top_surface_acceleration": "1000",
-    "top_surface_line_width": "100%",
-    "top_surface_speed": "30",
-    "travel_acceleration": "3500",
-    "version": "2.2.0.4",
-    "wall_generator": "classic",
-    "wall_loops": "3"
-}

process/0.24mm @Croesus.info

@@ -1,4 +1,4 @@
-sync_info = update
+sync_info = create
 user_id = 
 setting_id = 
 base_id = GP004

process/0.24mm @Croesus.json

@@ -18,13 +18,13 @@
     "ironing_spacing": "0.2",
     "ironing_speed": "180",
     "is_custom_defined": "0",
-    "name": "0.24mm Draft @Croesus",
+    "name": "0.24mm @Croesus",
     "only_one_wall_first_layer": "1",
     "only_one_wall_top": "1",
     "outer_wall_acceleration": "1000",
     "outer_wall_speed": "80",
     "precise_outer_wall": "1",
-    "print_settings_id": "0.24mm Draft @Croesus",
+    "print_settings_id": "0.24mm @Croesus",
     "skirt_height": "2",
     "skirt_loops": "1",
     "skirt_speed": "0",

process/0.24mm @Jensen.info

@@ -0,0 +1,5 @@
+sync_info = create
+user_id = 
+setting_id = 
+base_id = GP004
+updated_time = 0

process/0.24mm @Jensen.json

@@ -0,0 +1,18 @@
+{
+    "bottom_surface_pattern": "monotonicline",
+    "from": "User",
+    "inherits": "0.24mm Draft @Creality Ender3V3SE 0.4",
+    "initial_layer_print_height": "0.28",
+    "internal_solid_infill_pattern": "monotonicline",
+    "is_custom_defined": "0",
+    "name": "0.24mm @Jensen",
+    "only_one_wall_first_layer": "1",
+    "only_one_wall_top": "1",
+    "precise_outer_wall": "1",
+    "print_settings_id": "0.24mm @Jensen",
+    "skirt_loops": "1",
+    "sparse_infill_density": "40%",
+    "sparse_infill_pattern": "gyroid",
+    "version": "2.2.0.4",
+    "wall_generator": "classic"
+}

process/0.24mm Draft @TzKal-Zuk.json

@@ -1,49 +0,0 @@
-{
-    "bottom_solid_infill_flow_ratio": "1.05",
-    "bottom_surface_pattern": "monotonicline",
-    "bridge_flow": "1",
-    "bridge_speed": "60",
-    "detect_thin_wall": "0",
-    "enable_overhang_speed": "0",
-    "from": "User",
-    "gap_infill_speed": "15",
-    "inherits": "0.24mm Draft @Creality Ender3V3SE 0.4",
-    "initial_layer_infill_speed": "30",
-    "initial_layer_line_width": "120%",
-    "initial_layer_print_height": "0.28",
-    "initial_layer_speed": "15",
-    "inner_wall_acceleration": "1000",
-    "inner_wall_line_width": "110%",
-    "inner_wall_speed": "60",
-    "internal_bridge_speed": "80",
-    "internal_solid_infill_line_width": "120%",
-    "internal_solid_infill_pattern": "monotonicline",
-    "internal_solid_infill_speed": "100",
-    "is_custom_defined": "0",
-    "line_width": "110%",
-    "max_volumetric_extrusion_rate_slope": "15",
-    "name": "0.24mm Draft @TzKal-Zuk",
-    "only_one_wall_first_layer": "1",
-    "only_one_wall_top": "1",
-    "outer_wall_acceleration": "500",
-    "outer_wall_line_width": "100%",
-    "outer_wall_speed": "40",
-    "precise_outer_wall": "1",
-    "print_settings_id": "0.24mm Draft @TzKal-Zuk",
-    "skirt_loops": "1",
-    "small_perimeter_speed": "15",
-    "sparse_infill_acceleration": "200%",
-    "sparse_infill_density": "40%",
-    "sparse_infill_line_width": "160%",
-    "sparse_infill_pattern": "gyroid",
-    "sparse_infill_speed": "150",
-    "support_line_width": "96%",
-    "support_speed": "60",
-    "top_surface_acceleration": "1000",
-    "top_surface_line_width": "100%",
-    "top_surface_speed": "30",
-    "travel_acceleration": "3500",
-    "version": "2.2.0.4",
-    "wall_generator": "classic",
-    "wall_loops": "3"
-}

process/0.28mm @Croesus.info

@@ -1,4 +1,4 @@
-sync_info = update
+sync_info = create
 user_id = 
 setting_id = 
 base_id = GP004

process/0.28mm @Croesus.json

@@ -18,13 +18,13 @@
     "ironing_spacing": "0.2",
     "ironing_speed": "180",
     "is_custom_defined": "0",
-    "name": "0.28mm Extra Draft @Croesus",
+    "name": "0.28mm @Croesus",
     "only_one_wall_first_layer": "1",
     "only_one_wall_top": "1",
     "outer_wall_acceleration": "1000",
     "outer_wall_speed": "80",
     "precise_outer_wall": "1",
-    "print_settings_id": "0.28mm Extra Draft @Croesus",
+    "print_settings_id": "0.28mm @Croesus",
     "skirt_height": "2",
     "skirt_loops": "1",
     "skirt_speed": "0",

process/0.32mm @Croesus.info

@@ -1,4 +1,4 @@
-sync_info = update
+sync_info = create
 user_id = 
 setting_id = 
 base_id = GP004

process/0.32mm @Croesus.json

@@ -18,13 +18,13 @@
     "ironing_spacing": "0.2",
     "ironing_speed": "180",
     "is_custom_defined": "0",
-    "name": "0.32mm Standard @Croesus",
+    "name": "0.32mm @Croesus",
     "only_one_wall_first_layer": "1",
     "only_one_wall_top": "1",
     "outer_wall_acceleration": "1000",
     "outer_wall_speed": "80",
     "precise_outer_wall": "1",
-    "print_settings_id": "0.32mm Standard @Croesus",
+    "print_settings_id": "0.32mm @Croesus",
     "skirt_height": "2",
     "skirt_loops": "1",
     "skirt_speed": "0",