add essential configurations
This commit is contained in:
commit
c9b4a94fb6
5
.gitignore
vendored
Normal file
5
.gitignore
vendored
Normal file
|
|
@ -0,0 +1,5 @@
|
||||||
|
*
|
||||||
|
!.gitignore
|
||||||
|
!printer.cfg
|
||||||
|
!btt-ebb36.cfg
|
||||||
|
!macros.cfg
|
||||||
83
btt-ebb36.cfg
Normal file
83
btt-ebb36.cfg
Normal file
|
|
@ -0,0 +1,83 @@
|
||||||
|
# This file contains common pin mappings for the BIGTREETECH EBBCan
|
||||||
|
# Canbus board. To use this config, the firmware should be compiled for the
|
||||||
|
# STM32G0B1 with "8 MHz crystal" and "USB (on PA11/PA12)" or "CAN bus (on PB0/PB1)".
|
||||||
|
# The "EBB Can" micro-controller will be used to control the components on the nozzle.
|
||||||
|
|
||||||
|
# See docs/Config_Reference.md for a description of parameters.
|
||||||
|
|
||||||
|
[mcu EBBCan]
|
||||||
|
canbus_uuid: 8313b2b130fc
|
||||||
|
|
||||||
|
[thermistor DREMC NTC100K B3950]
|
||||||
|
temperature1: 25.0
|
||||||
|
resistance1: 103180.0
|
||||||
|
temperature2: 150.0
|
||||||
|
resistance2: 1366.2
|
||||||
|
temperature3: 250.0
|
||||||
|
resistance3: 168.6
|
||||||
|
|
||||||
|
[extruder]
|
||||||
|
step_pin: EBBCan: PD0
|
||||||
|
dir_pin: EBBCan: PD1
|
||||||
|
enable_pin: !EBBCan: PD2
|
||||||
|
microsteps: 16
|
||||||
|
full_steps_per_rotation: 200
|
||||||
|
rotation_distance: 4.682442
|
||||||
|
nozzle_diameter: 0.400
|
||||||
|
filament_diameter: 1.750
|
||||||
|
max_extrude_cross_section: 5
|
||||||
|
max_extrude_only_distance: 500
|
||||||
|
max_extrude_only_velocity: 120
|
||||||
|
pressure_advance: 0.045
|
||||||
|
pressure_advance_smooth_time: 0.03
|
||||||
|
heater_pin: EBBCan: PB13
|
||||||
|
sensor_type: DREMC NTC100K B3950
|
||||||
|
sensor_pin: EBBCan: PA3
|
||||||
|
control: pid
|
||||||
|
pid_Kp: 27.153
|
||||||
|
pid_Ki: 1.661
|
||||||
|
pid_Kd: 110.989
|
||||||
|
min_extrude_temp: 180
|
||||||
|
min_temp: 0
|
||||||
|
max_temp: 250
|
||||||
|
|
||||||
|
[tmc2209 extruder]
|
||||||
|
uart_pin: EBBCan: PA15
|
||||||
|
run_current: 0.650 # Max 0.850
|
||||||
|
driver_TBL: 0
|
||||||
|
driver_HEND: 6
|
||||||
|
driver_HSTRT: 7
|
||||||
|
driver_TOFF: 4
|
||||||
|
|
||||||
|
[fan]
|
||||||
|
pin: EBBCan: PA0
|
||||||
|
|
||||||
|
[heater_fan hotend_fan]
|
||||||
|
pin: EBBCan: PA1
|
||||||
|
heater: extruder
|
||||||
|
heater_temp: 50.0
|
||||||
|
|
||||||
|
[bltouch]
|
||||||
|
sensor_pin: ^EBBCan:PB8
|
||||||
|
control_pin: EBBCan:PB9
|
||||||
|
x_offset: 0
|
||||||
|
y_offset: 22.5
|
||||||
|
z_offset: 1.825
|
||||||
|
speed: 20
|
||||||
|
samples: 3
|
||||||
|
sample_retract_dist: 5.0
|
||||||
|
samples_result: median
|
||||||
|
samples_tolerance: 0.01
|
||||||
|
samples_tolerance_retries: 3
|
||||||
|
|
||||||
|
[safe_z_home]
|
||||||
|
home_xy_position: 115,82.5
|
||||||
|
speed: 150
|
||||||
|
z_hop: 10
|
||||||
|
z_hop_speed: 10
|
||||||
|
|
||||||
|
[adxl345 hotend]
|
||||||
|
cs_pin: EBBCan: PB12
|
||||||
|
spi_software_sclk_pin: EBBCan: PB10
|
||||||
|
spi_software_mosi_pin: EBBCan: PB11
|
||||||
|
spi_software_miso_pin: EBBCan: PB2
|
||||||
118
macros.cfg
Normal file
118
macros.cfg
Normal file
|
|
@ -0,0 +1,118 @@
|
||||||
|
# This file provides Klipper G-Code macros.
|
||||||
|
|
||||||
|
# See docs/Config_Reference.md for a description of parameters.
|
||||||
|
|
||||||
|
|
||||||
|
######################################################################
|
||||||
|
# Start Print and End Print
|
||||||
|
######################################################################
|
||||||
|
|
||||||
|
# Replace the slicer's custom start and end g-code scripts with
|
||||||
|
# START_PRINT and END_PRINT. See docs/Slicers.md for more information on using these macros.
|
||||||
|
|
||||||
|
[gcode_macro START_PRINT]
|
||||||
|
gcode:
|
||||||
|
# This part fetches data from your slicer. Such as bed temp, extruder temp and size of your printer.
|
||||||
|
{% set target_bed = params.BED|int %}
|
||||||
|
{% set target_extruder = params.EXTRUDER|int %}
|
||||||
|
{% set x_wait = printer.toolhead.axis_maximum.x|float / 2 %}
|
||||||
|
{% set y_wait = printer.toolhead.axis_maximum.y|float / 2 %}
|
||||||
|
|
||||||
|
# Homes the printer, sets absolute positioning, update the Stealthburner leds and clear old bed mesh.
|
||||||
|
STATUS_HOMING # Sets SB-leds to homing-mode
|
||||||
|
G28 # Full home (XYZ)
|
||||||
|
G90 # Absolute position
|
||||||
|
BED_MESH_CLEAR # Clears old saved bed mesh (if any)
|
||||||
|
|
||||||
|
# Heat up the bed with 5 minute soak.
|
||||||
|
RESPOND TYPE=echo_no_space MSG="Bed: {target_bed}c" # Displays info
|
||||||
|
STATUS_HEATING # Sets SB-leds to heating-mode
|
||||||
|
G1 X{x_wait} Y{y_wait} Z15 F9000 # Goes to center of the bed
|
||||||
|
M190 S{target_bed} # Sets the target temp for the bed
|
||||||
|
RESPOND TYPE=echo_no_space MSG="Soak for 5min" # Displays info
|
||||||
|
G4 P300000 # Waits 5 min for the bedtemp to stabilize
|
||||||
|
|
||||||
|
# Heating nozzle to 150 degrees. This helps with getting a correct Z-home
|
||||||
|
RESPOND TYPE=echo_no_space MSG="Hotend: 150c" # Displays info
|
||||||
|
M109 S150 # Heats the nozzle to 150c
|
||||||
|
|
||||||
|
# Adjust for gantry tilt.
|
||||||
|
RESPOND TYPE=echo_no_space MSG="Z-tilt adjust" # Displays info
|
||||||
|
STATUS_LEVELING # Sets SB-leds to leveling-mode
|
||||||
|
Z_TILT_ADJUST # Levels the x gantry via z_tilt_adjust
|
||||||
|
G28 Z # Homes Z again after z_tilt_adjust
|
||||||
|
|
||||||
|
# Take a mesh of the bed.
|
||||||
|
RESPOND TYPE=echo_no_space MSG="Bed mesh" # Displays info
|
||||||
|
STATUS_MESHING # Sets SB-leds to bed mesh-mode
|
||||||
|
BED_MESH_CALIBRATE # Starts bed mesh
|
||||||
|
|
||||||
|
# Parks the printhead, update the SB-leds and heat the nozzle.
|
||||||
|
RESPOND TYPE=echo_no_space MSG="Hotend: {target_extruder}c" # Displays info
|
||||||
|
STATUS_HEATING # Sets SB-leds to heating-mode
|
||||||
|
SMART_PARK # Move the printhead near the print area
|
||||||
|
M109 S{target_extruder} # Heats the nozzle to printing temp
|
||||||
|
|
||||||
|
# Gets ready to print by doing a purge line and updating the SB-leds
|
||||||
|
RESPOND TYPE=echo_no_space MSG="Printer goes brr" # Displays info
|
||||||
|
STATUS_PRINTING # Sets SB-leds to printing-mode
|
||||||
|
LINE_PURGE # Purge line
|
||||||
|
G90 # Absolute position
|
||||||
|
|
||||||
|
[gcode_macro END_PRINT]
|
||||||
|
gcode:
|
||||||
|
# Fetch maximum position for axis
|
||||||
|
{% set x_max = printer.toolhead.axis_maximum.x %}
|
||||||
|
{% set y_max = printer.toolhead.axis_maximum.y %}
|
||||||
|
|
||||||
|
# Turn off bed, extruder, and fan
|
||||||
|
M140 S0
|
||||||
|
M104 S0
|
||||||
|
M106 S0
|
||||||
|
|
||||||
|
# Move nozzle away from print while retracting
|
||||||
|
G91
|
||||||
|
G1 X-2 Y-2 E-3 F300
|
||||||
|
|
||||||
|
# Raise nozzle by 10mm
|
||||||
|
G1 Z10 F3000
|
||||||
|
G90
|
||||||
|
|
||||||
|
# Present print
|
||||||
|
G1 X{x_max} Y{y_max}
|
||||||
|
|
||||||
|
# Disable steppers
|
||||||
|
M84
|
||||||
|
|
||||||
|
######################################################################
|
||||||
|
# Filament Change
|
||||||
|
######################################################################
|
||||||
|
|
||||||
|
# M600: Filament Change. This macro will pause the printer, move the
|
||||||
|
# tool to the change position, and retract the filament 50mm. Adjust
|
||||||
|
# the retraction settings for your own extruder. After filament has
|
||||||
|
# been changed, the print can be resumed from its previous position
|
||||||
|
# with the "RESUME" gcode.
|
||||||
|
|
||||||
|
[pause_resume]
|
||||||
|
|
||||||
|
[gcode_macro M600]
|
||||||
|
gcode:
|
||||||
|
{% set X = params.X|default(50)|float %}
|
||||||
|
{% set Y = params.Y|default(0)|float %}
|
||||||
|
{% set Z = params.Z|default(10)|float %}
|
||||||
|
SAVE_GCODE_STATE NAME=M600_state
|
||||||
|
PAUSE
|
||||||
|
G91
|
||||||
|
G1 E-.8 F2700
|
||||||
|
G1 Z{Z}
|
||||||
|
G90
|
||||||
|
G1 X{X} Y{Y} F3000
|
||||||
|
FILAMENT_UNLOAD # Use orbiter sensor unload macro
|
||||||
|
RESTORE_GCODE_STATE NAME=M600_state
|
||||||
|
|
||||||
|
# Enable the "M118" and "RESPOND" extended commands.
|
||||||
|
[respond]
|
||||||
|
|
||||||
|
# Enable object exclusion
|
||||||
|
[exclude_object]
|
||||||
180
printer.cfg
Normal file
180
printer.cfg
Normal file
|
|
@ -0,0 +1,180 @@
|
||||||
|
# This file contains common pin mappings for the BIGTREETECH Manta E3EZ
|
||||||
|
# To use this config, the firmware should be compiled for the
|
||||||
|
# STM32G0B1 with a "8KiB bootloader" "8 MHz crystal"
|
||||||
|
# and "USB (on PA11/PA12)" or "CAN bus (on PB12/PB13)".
|
||||||
|
|
||||||
|
# See docs/Config_Reference.md for a description of parameters.
|
||||||
|
[include mainsail.cfg]
|
||||||
|
[include btt-ebb36.cfg]
|
||||||
|
[include stealthburner_leds.cfg]
|
||||||
|
[include OrbiterSensor.cfg]
|
||||||
|
[include KAMP_Settings.cfg]
|
||||||
|
[include macros.cfg]
|
||||||
|
|
||||||
|
[mcu]
|
||||||
|
canbus_uuid: f4ecb7c12108
|
||||||
|
|
||||||
|
[stepper_x]
|
||||||
|
step_pin: PA14
|
||||||
|
dir_pin: !PA10
|
||||||
|
enable_pin: !PA13
|
||||||
|
microsteps: 16
|
||||||
|
rotation_distance: 40
|
||||||
|
endstop_pin: ^PC4
|
||||||
|
position_endstop: 0
|
||||||
|
position_min: 0
|
||||||
|
position_max: 245
|
||||||
|
homing_speed: 50
|
||||||
|
|
||||||
|
[stepper_y]
|
||||||
|
step_pin: PC8
|
||||||
|
dir_pin: !PA15
|
||||||
|
enable_pin: !PC14
|
||||||
|
microsteps: 16
|
||||||
|
rotation_distance: 40
|
||||||
|
endstop_pin: ^PB0
|
||||||
|
position_endstop: -20
|
||||||
|
position_min: -20
|
||||||
|
position_max: 210
|
||||||
|
homing_speed: 50
|
||||||
|
|
||||||
|
[stepper_z]
|
||||||
|
step_pin: PD2
|
||||||
|
dir_pin: !PD4
|
||||||
|
enable_pin: !PD3
|
||||||
|
microsteps: 16
|
||||||
|
rotation_distance: 8
|
||||||
|
endstop_pin: probe:z_virtual_endstop
|
||||||
|
position_min: -3
|
||||||
|
position_max: 200
|
||||||
|
|
||||||
|
[stepper_z1]
|
||||||
|
step_pin: PB7
|
||||||
|
dir_pin: !PB6
|
||||||
|
enable_pin: !PB4
|
||||||
|
microsteps: 16
|
||||||
|
rotation_distance: 8
|
||||||
|
|
||||||
|
[heater_bed]
|
||||||
|
heater_pin: PB2 #HB
|
||||||
|
sensor_type: EPCOS 100K B57560G104F #Generic 3950
|
||||||
|
sensor_pin: PA3 #TB
|
||||||
|
control: pid
|
||||||
|
pid_Kp: 68.457
|
||||||
|
pid_Ki: 1.138
|
||||||
|
pid_Kd: 1029.416
|
||||||
|
min_temp: 0
|
||||||
|
max_temp: 130
|
||||||
|
|
||||||
|
[printer]
|
||||||
|
kinematics: cartesian
|
||||||
|
max_velocity: 180
|
||||||
|
max_accel: 5000
|
||||||
|
max_z_velocity: 5
|
||||||
|
max_z_accel: 100
|
||||||
|
|
||||||
|
########################################
|
||||||
|
# TMC2209 configuration
|
||||||
|
########################################
|
||||||
|
|
||||||
|
[tmc2209 stepper_x]
|
||||||
|
uart_pin: PB8
|
||||||
|
run_current: 0.580
|
||||||
|
#stealthchop_threshold: 999999
|
||||||
|
|
||||||
|
[tmc2209 stepper_y]
|
||||||
|
uart_pin: PC9
|
||||||
|
run_current: 0.580
|
||||||
|
#stealthchop_threshold: 999999
|
||||||
|
|
||||||
|
[tmc2209 stepper_z]
|
||||||
|
uart_pin: PD0
|
||||||
|
run_current: 0.580
|
||||||
|
#stealthchop_threshold: 999999
|
||||||
|
|
||||||
|
[tmc2209 stepper_z1]
|
||||||
|
uart_pin: PB5
|
||||||
|
run_current: 0.580
|
||||||
|
#stealthchop_threshold: 999999
|
||||||
|
|
||||||
|
[firmware_retraction]
|
||||||
|
retract_length: 0.5
|
||||||
|
retract_speed: 35
|
||||||
|
unretract_speed: 35
|
||||||
|
|
||||||
|
[adxl345 bed]
|
||||||
|
cs_pin: PC15
|
||||||
|
spi_software_miso_pin: PC11
|
||||||
|
spi_software_mosi_pin: PC12
|
||||||
|
spi_software_sclk_pin: PC10
|
||||||
|
|
||||||
|
[resonance_tester]
|
||||||
|
accel_chip_x: adxl345 hotend
|
||||||
|
accel_chip_y: adxl345 bed
|
||||||
|
probe_points: 115,82.5,10
|
||||||
|
|
||||||
|
[bed_screws]
|
||||||
|
screw1: 30, 30
|
||||||
|
screw2: 200, 30
|
||||||
|
screw3: 200, 200
|
||||||
|
screw4: 30, 200
|
||||||
|
|
||||||
|
[screws_tilt_adjust]
|
||||||
|
screw1: 30, 7.5
|
||||||
|
screw1_name: front left screw
|
||||||
|
screw2: 200, 7.5
|
||||||
|
screw2_name: front right screw
|
||||||
|
screw3: 200, 177.5
|
||||||
|
screw3_name: rear right screw
|
||||||
|
screw4: 30, 177.5
|
||||||
|
screw4_name: rear left screw
|
||||||
|
horizontal_move_z: 10
|
||||||
|
speed: 50
|
||||||
|
screw_thread: CW-M4 # Use CW for Clockwise and CCW for Counter Clockwise
|
||||||
|
|
||||||
|
[z_tilt]
|
||||||
|
z_positions:
|
||||||
|
-30,110
|
||||||
|
260,110
|
||||||
|
points:
|
||||||
|
10,110
|
||||||
|
220,110
|
||||||
|
retries: 20
|
||||||
|
retry_tolerance: 0.005
|
||||||
|
|
||||||
|
[bed_mesh]
|
||||||
|
speed: 50
|
||||||
|
mesh_min: 10,10 # Need to handle head distance with cr-touch (bl_touch)
|
||||||
|
mesh_max: 220,200 # Max probe range
|
||||||
|
probe_count: 11,11
|
||||||
|
fade_start: 1
|
||||||
|
fade_end: 10
|
||||||
|
fade_target: 0
|
||||||
|
algorithm: bicubic
|
||||||
|
bicubic_tension: 0.5
|
||||||
|
|
||||||
|
[shaketune]
|
||||||
|
result_folder: ~/printer_data/config/ShakeTune_results
|
||||||
|
number_of_results_to_keep: 3
|
||||||
|
keep_raw_csv: False
|
||||||
|
show_macros_in_webui: True
|
||||||
|
timeout: 300
|
||||||
|
|
||||||
|
[input_shaper]
|
||||||
|
shaper_freq_x: 116.0
|
||||||
|
shaper_freq_y: 52.2
|
||||||
|
shaper_type_x: mzv
|
||||||
|
shaper_type_y: ei
|
||||||
|
damping_ratio_x: 0.022
|
||||||
|
damping_ratio_y: 0.035
|
||||||
|
|
||||||
|
[virtual_sdcard]
|
||||||
|
path: /home/biqu/printer_data/gcodes
|
||||||
|
on_error_gcode: CANCEL_PRINT
|
||||||
|
|
||||||
|
# Mainsail macro variables
|
||||||
|
[gcode_macro _CLIENT_VARIABLE]
|
||||||
|
variable_speed_move : 50.0
|
||||||
|
variable_use_fw_retract : True
|
||||||
|
variable_idle_timeout : 3600
|
||||||
|
gcode:
|
||||||
Loading…
Reference in a new issue