refactor
This commit is contained in:
parent
dcac9d16b9
commit
568fff23c1
GPG key ID:
8563E358D4E8040E
|
|
@ -1,83 +0,0 @@
|
||||||
# This file contains common pin mappings for the BIGTREETECH EBBCan
|
|
||||||
# Canbus board. To use this config, the firmware should be compiled for the
|
|
||||||
# STM32G0B1 with "8 MHz crystal" and "USB (on PA11/PA12)" or "CAN bus (on PB0/PB1)".
|
|
||||||
# The "EBB Can" micro-controller will be used to control the components on the nozzle.
|
|
||||||
|
|
||||||
# See docs/Config_Reference.md for a description of parameters.
|
|
||||||
|
|
||||||
[mcu EBBCan]
|
|
||||||
canbus_uuid: 8313b2b130fc
|
|
||||||
|
|
||||||
[thermistor DREMC NTC100K B3950]
|
|
||||||
temperature1: 25.0
|
|
||||||
resistance1: 103180.0
|
|
||||||
temperature2: 150.0
|
|
||||||
resistance2: 1366.2
|
|
||||||
temperature3: 250.0
|
|
||||||
resistance3: 168.6
|
|
||||||
|
|
||||||
[extruder]
|
|
||||||
step_pin: EBBCan: PD0
|
|
||||||
dir_pin: EBBCan: PD1
|
|
||||||
enable_pin: !EBBCan: PD2
|
|
||||||
microsteps: 16
|
|
||||||
full_steps_per_rotation: 200
|
|
||||||
rotation_distance: 4.729266
|
|
||||||
nozzle_diameter: 0.400
|
|
||||||
filament_diameter: 1.750
|
|
||||||
max_extrude_cross_section: 5
|
|
||||||
max_extrude_only_distance: 500
|
|
||||||
max_extrude_only_velocity: 120
|
|
||||||
pressure_advance: 0.025 #to be calibrated
|
|
||||||
pressure_advance_smooth_time: 0.03 #to be calibrated
|
|
||||||
heater_pin: EBBCan: PB13
|
|
||||||
sensor_type: DREMC NTC100K B3950
|
|
||||||
sensor_pin: EBBCan: PA3
|
|
||||||
control: pid
|
|
||||||
pid_Kp: 25.60
|
|
||||||
pid_Ki: 1.369
|
|
||||||
pid_Kd: 116.510
|
|
||||||
min_extrude_temp: 180
|
|
||||||
min_temp: 0
|
|
||||||
max_temp: 300
|
|
||||||
|
|
||||||
[tmc2209 extruder]
|
|
||||||
uart_pin: EBBCan: PA15
|
|
||||||
run_current: 0.650 # Max 0.850
|
|
||||||
driver_TBL: 0
|
|
||||||
driver_HEND: 6
|
|
||||||
driver_HSTRT: 7
|
|
||||||
driver_TOFF: 4
|
|
||||||
|
|
||||||
[fan]
|
|
||||||
pin: EBBCan: PA0
|
|
||||||
|
|
||||||
[heater_fan hotend_fan]
|
|
||||||
pin: EBBCan: PA1
|
|
||||||
heater: extruder
|
|
||||||
heater_temp: 50.0
|
|
||||||
|
|
||||||
[bltouch]
|
|
||||||
sensor_pin: ^EBBCan:PB8
|
|
||||||
control_pin: EBBCan:PB9
|
|
||||||
x_offset: 0
|
|
||||||
y_offset: 22.5
|
|
||||||
z_offset: 2.005
|
|
||||||
speed: 20
|
|
||||||
samples: 3
|
|
||||||
sample_retract_dist: 5.0
|
|
||||||
samples_result: median
|
|
||||||
samples_tolerance: 0.0125
|
|
||||||
samples_tolerance_retries: 3
|
|
||||||
|
|
||||||
[safe_z_home]
|
|
||||||
home_xy_position: 115,82.5
|
|
||||||
speed: 150
|
|
||||||
z_hop: 10
|
|
||||||
z_hop_speed: 10
|
|
||||||
|
|
||||||
[adxl345 hotend]
|
|
||||||
cs_pin: EBBCan: PB12
|
|
||||||
spi_software_sclk_pin: EBBCan: PB10
|
|
||||||
spi_software_mosi_pin: EBBCan: PB11
|
|
||||||
spi_software_miso_pin: EBBCan: PB2
|
|
||||||
201
printer.cfg
201
printer.cfg
|
|
@ -3,16 +3,118 @@
|
||||||
# STM32G0B1 with a "8KiB bootloader" "8 MHz crystal"
|
# STM32G0B1 with a "8KiB bootloader" "8 MHz crystal"
|
||||||
# and "USB (on PA11/PA12)" or "CAN bus (on PB12/PB13)".
|
# and "USB (on PA11/PA12)" or "CAN bus (on PB12/PB13)".
|
||||||
|
|
||||||
|
# This file also contains common pin mappings for the BIGTREETECH EBBCan
|
||||||
|
# Canbus board. To use this config, the firmware should be compiled for the
|
||||||
|
# STM32G0B1 with "8 MHz crystal" and "USB (on PA11/PA12)" or "CAN bus (on PB0/PB1)".
|
||||||
|
# The "EBB Can" micro-controller will be used to control the components on the nozzle.
|
||||||
|
|
||||||
# See docs/Config_Reference.md for a description of parameters.
|
# See docs/Config_Reference.md for a description of parameters.
|
||||||
|
|
||||||
|
#######################################
|
||||||
|
# Includes
|
||||||
|
########################################
|
||||||
|
|
||||||
|
# Core
|
||||||
[include mainsail.cfg]
|
[include mainsail.cfg]
|
||||||
[include btt-ebb36.cfg]
|
[include macros.cfg]
|
||||||
|
# Toolhead
|
||||||
[include stealthburner_leds.cfg]
|
[include stealthburner_leds.cfg]
|
||||||
[include OrbiterSensor.cfg]
|
[include OrbiterSensor.cfg]
|
||||||
|
# Plugins
|
||||||
[include KAMP_Settings.cfg]
|
[include KAMP_Settings.cfg]
|
||||||
[include macros.cfg]
|
|
||||||
|
########################################
|
||||||
|
# Microcontrollers
|
||||||
|
########################################
|
||||||
|
|
||||||
[mcu]
|
[mcu]
|
||||||
canbus_uuid: f4ecb7c12108
|
canbus_uuid: f4ecb7c12108
|
||||||
|
[mcu EBBCan]
|
||||||
|
canbus_uuid: 8313b2b130fc
|
||||||
|
|
||||||
|
########################################
|
||||||
|
# Printer Configuration
|
||||||
|
########################################
|
||||||
|
|
||||||
|
[printer]
|
||||||
|
kinematics: cartesian
|
||||||
|
max_velocity: 450
|
||||||
|
max_accel: 10000
|
||||||
|
max_z_velocity: 5
|
||||||
|
max_z_accel: 100
|
||||||
|
|
||||||
|
[safe_z_home]
|
||||||
|
home_xy_position: 115,82.5
|
||||||
|
speed: 150
|
||||||
|
z_hop: 10
|
||||||
|
z_hop_speed: 10
|
||||||
|
|
||||||
|
[firmware_retraction]
|
||||||
|
retract_length: 0.5
|
||||||
|
retract_speed: 35
|
||||||
|
unretract_speed: 35
|
||||||
|
|
||||||
|
[virtual_sdcard]
|
||||||
|
path: /home/biqu/printer_data/gcodes
|
||||||
|
on_error_gcode: CANCEL_PRINT
|
||||||
|
|
||||||
|
########################################
|
||||||
|
# Mainsail Configuration
|
||||||
|
########################################
|
||||||
|
|
||||||
|
[gcode_macro _CLIENT_VARIABLE]
|
||||||
|
variable_speed_move : 50.0
|
||||||
|
variable_use_fw_retract : True
|
||||||
|
variable_idle_timeout : 3600
|
||||||
|
gcode:
|
||||||
|
|
||||||
|
########################################
|
||||||
|
# Printer Components
|
||||||
|
########################################
|
||||||
|
|
||||||
|
[fan]
|
||||||
|
pin: EBBCan: PA0
|
||||||
|
|
||||||
|
[heater_fan hotend_fan]
|
||||||
|
pin: EBBCan: PA1
|
||||||
|
heater: extruder
|
||||||
|
heater_temp: 50.0
|
||||||
|
|
||||||
|
[bltouch]
|
||||||
|
sensor_pin: ^EBBCan:PB8
|
||||||
|
control_pin: EBBCan:PB9
|
||||||
|
x_offset: 0
|
||||||
|
y_offset: 22.5
|
||||||
|
z_offset: 2.005
|
||||||
|
speed: 20
|
||||||
|
samples: 3
|
||||||
|
sample_retract_dist: 5.0
|
||||||
|
samples_result: median
|
||||||
|
samples_tolerance: 0.0125
|
||||||
|
samples_tolerance_retries: 3
|
||||||
|
|
||||||
|
[thermistor DREMC NTC100K B3950]
|
||||||
|
temperature1: 25.0
|
||||||
|
resistance1: 103180.0
|
||||||
|
temperature2: 150.0
|
||||||
|
resistance2: 1366.2
|
||||||
|
temperature3: 250.0
|
||||||
|
resistance3: 168.6
|
||||||
|
|
||||||
|
[heater_bed]
|
||||||
|
heater_pin: PB2 #HB
|
||||||
|
sensor_type: EPCOS 100K B57560G104F #Generic 3950
|
||||||
|
sensor_pin: PA3 #TB
|
||||||
|
control: pid
|
||||||
|
pid_Kp: 68.457
|
||||||
|
pid_Ki: 1.138
|
||||||
|
pid_Kd: 1029.416
|
||||||
|
min_temp: 0
|
||||||
|
max_temp: 130
|
||||||
|
|
||||||
|
########################################
|
||||||
|
# Stepper Configuration
|
||||||
|
########################################
|
||||||
|
|
||||||
[stepper_x]
|
[stepper_x]
|
||||||
step_pin: PA14
|
step_pin: PA14
|
||||||
|
|
@ -55,26 +157,33 @@ enable_pin: !PB4
|
||||||
microsteps: 16
|
microsteps: 16
|
||||||
rotation_distance: 8
|
rotation_distance: 8
|
||||||
|
|
||||||
[heater_bed]
|
[extruder]
|
||||||
heater_pin: PB2 #HB
|
step_pin: EBBCan: PD0
|
||||||
sensor_type: EPCOS 100K B57560G104F #Generic 3950
|
dir_pin: EBBCan: PD1
|
||||||
sensor_pin: PA3 #TB
|
enable_pin: !EBBCan: PD2
|
||||||
|
microsteps: 16
|
||||||
|
full_steps_per_rotation: 200
|
||||||
|
rotation_distance: 4.729266
|
||||||
|
nozzle_diameter: 0.400
|
||||||
|
filament_diameter: 1.750
|
||||||
|
max_extrude_cross_section: 5
|
||||||
|
max_extrude_only_distance: 500
|
||||||
|
max_extrude_only_velocity: 120
|
||||||
|
pressure_advance: 0.025 #to be calibrated
|
||||||
|
pressure_advance_smooth_time: 0.03 #to be calibrated
|
||||||
|
heater_pin: EBBCan: PB13
|
||||||
|
sensor_type: DREMC NTC100K B3950
|
||||||
|
sensor_pin: EBBCan: PA3
|
||||||
control: pid
|
control: pid
|
||||||
pid_Kp: 68.457
|
pid_Kp: 25.60
|
||||||
pid_Ki: 1.138
|
pid_Ki: 1.369
|
||||||
pid_Kd: 1029.416
|
pid_Kd: 116.510
|
||||||
|
min_extrude_temp: 180
|
||||||
min_temp: 0
|
min_temp: 0
|
||||||
max_temp: 130
|
max_temp: 300
|
||||||
|
|
||||||
[printer]
|
|
||||||
kinematics: cartesian
|
|
||||||
max_velocity: 450
|
|
||||||
max_accel: 10000
|
|
||||||
max_z_velocity: 5
|
|
||||||
max_z_accel: 100
|
|
||||||
|
|
||||||
########################################
|
########################################
|
||||||
# TMC2209 configuration
|
# TMC2209 Configuration
|
||||||
########################################
|
########################################
|
||||||
|
|
||||||
[tmc2209 stepper_x]
|
[tmc2209 stepper_x]
|
||||||
|
|
@ -97,21 +206,17 @@ uart_pin: PB5
|
||||||
run_current: 0.580
|
run_current: 0.580
|
||||||
interpolate: True
|
interpolate: True
|
||||||
|
|
||||||
[firmware_retraction]
|
[tmc2209 extruder]
|
||||||
retract_length: 0.5
|
uart_pin: EBBCan: PA15
|
||||||
retract_speed: 35
|
run_current: 0.650 # Max 0.850
|
||||||
unretract_speed: 35
|
driver_TBL: 0
|
||||||
|
driver_HEND: 6
|
||||||
|
driver_HSTRT: 7
|
||||||
|
driver_TOFF: 4
|
||||||
|
|
||||||
[adxl345 bed]
|
########################################
|
||||||
cs_pin: PC15
|
# Bed Leveling
|
||||||
spi_software_miso_pin: PC11
|
########################################
|
||||||
spi_software_mosi_pin: PC12
|
|
||||||
spi_software_sclk_pin: PC10
|
|
||||||
|
|
||||||
[resonance_tester]
|
|
||||||
accel_chip_x: adxl345 hotend
|
|
||||||
accel_chip_y: adxl345 bed
|
|
||||||
probe_points: 115,82.5,10
|
|
||||||
|
|
||||||
[bed_screws]
|
[bed_screws]
|
||||||
screw1: 30, 30
|
screw1: 30, 30
|
||||||
|
|
@ -154,6 +259,27 @@ fade_target: 0
|
||||||
algorithm: bicubic
|
algorithm: bicubic
|
||||||
bicubic_tension: 0.5
|
bicubic_tension: 0.5
|
||||||
|
|
||||||
|
########################################
|
||||||
|
# Resonance Compensation
|
||||||
|
########################################
|
||||||
|
|
||||||
|
[adxl345 hotend]
|
||||||
|
cs_pin: EBBCan: PB12
|
||||||
|
spi_software_sclk_pin: EBBCan: PB10
|
||||||
|
spi_software_mosi_pin: EBBCan: PB11
|
||||||
|
spi_software_miso_pin: EBBCan: PB2
|
||||||
|
|
||||||
|
[adxl345 bed]
|
||||||
|
cs_pin: PC15
|
||||||
|
spi_software_miso_pin: PC11
|
||||||
|
spi_software_mosi_pin: PC12
|
||||||
|
spi_software_sclk_pin: PC10
|
||||||
|
|
||||||
|
[resonance_tester]
|
||||||
|
accel_chip_x: adxl345 hotend
|
||||||
|
accel_chip_y: adxl345 bed
|
||||||
|
probe_points: 115,82.5,10
|
||||||
|
|
||||||
[shaketune]
|
[shaketune]
|
||||||
result_folder: ~/printer_data/config/ShakeTune_results
|
result_folder: ~/printer_data/config/ShakeTune_results
|
||||||
number_of_results_to_keep: 3
|
number_of_results_to_keep: 3
|
||||||
|
|
@ -168,14 +294,3 @@ shaper_type_x: ei
|
||||||
shaper_type_y: ei
|
shaper_type_y: ei
|
||||||
damping_ratio_x: 0.040
|
damping_ratio_x: 0.040
|
||||||
damping_ratio_y: 0.039
|
damping_ratio_y: 0.039
|
||||||
|
|
||||||
[virtual_sdcard]
|
|
||||||
path: /home/biqu/printer_data/gcodes
|
|
||||||
on_error_gcode: CANCEL_PRINT
|
|
||||||
|
|
||||||
# Mainsail macro variables
|
|
||||||
[gcode_macro _CLIENT_VARIABLE]
|
|
||||||
variable_speed_move : 50.0
|
|
||||||
variable_use_fw_retract : True
|
|
||||||
variable_idle_timeout : 3600
|
|
||||||
gcode:
|
|
||||||
|
|
|
||||||
Loading…
Reference in a new issue